My Planes are Taking Shape!

On the fourth day of the Scott Meek class on making wooden planes, we shaped the wedges that will hold our blades in place and then began to cut the now rectangular plane bodies to their final shapes.
For my Osage orange smoothing plane, which has a 50 degree bed angle, I decided to create my own body style and so I strayed from the traditional design. 

The Osage orange smoother body before shaping

My idea was to incorporate handle-like curves in the toe and rear of the plane to make it more easily fit my hand in use.  So I left the front and rear sections higher so I could shape them to fit my hand.

Some of the shaping is visible on the front of the plane; I did less shaping on the rear

I will probably not make any more changes to this plane, except to polish the rasped areas.  I can do additional changes to fit my hand when I'm back in my own woodshop and after I have spent some time using the plane.

My teak jack plane in the process of being shaped

The teak 12 inch jack plane is still being shaped.  I'm following Scott's pattern for this plane, which will have Scott's "wave" pattern on the rear section.  That not only makes it easy to hold and use, but beautiful as well.

I've not yet started on shaping the 22 inch white oak jointer.  That will come tomorrow.

My teak jointer and Osage orange smoother as they near completion

Some of the 12 planes being built in the class this week

Tomorrow we'll finish shaping the bodies and then work the mouths so the blades protrude just the right amount.

Need I say that I'm having a lot of fun--and learning a lot too!--in this class?  When I update my book on handplanes, Choosing and Using Handplanes, I plan to include a chapter on wooden handplanes, which are quickly becoming favorites in my handplane collection.

Norm

Starting to Look Like Planes

In yesterday's class, we made the cross pins, against which the wedges will secure the blade in place, and cut the cheeks off the sides of the plane blocks; until now they had been whole blocks.  Then we cut the center block into two with the correct slopes to bed the plane blade at the desired angle.  My smoother is being crafted from Osage orange, a very hard and beautiful yellow wood.  Domestic varieties are also known as hedge apple and by other names.

I then marked the location for the crosspin, drilled holes through the body to accept it, and glued the cheeks back onto the center blocks.

The Osage orange smoother in clamps after the cheeks were re-glued to the center blocks

The clamps came off after a few hours.  I centered the crosspin between the checks, trimmed off the crosspins where they stood proud, and laid out the profile for the plane on one side.  Then it was off to the bandsaw to create the rough outline shown below.

After the clamps came off, the boxy plane body was sawn to rough shape

Next steps are to refine the body shape, hone the blade and fit the blade and the wedge to the plane body.

Norm

Day 2--Scott Meek Plane Class

We made great progress in constructing our planes today. Those blanks, like the Osage orange shown, that were glued with epoxy, came out of the clamps this morning.  We jointed the bottom and one reference edge, then planed the blanks to rough width.

Osage orange plane blank with applied sole in Ipe glued on

The Osage orange blank viewed from the end on; doesn't look like much does it?

 Then we cut the cheeks from the edges, leaving behind a center block to be further cut to accommodate a blade. 

The center sections of two planes marked and partially bandsawn, awaiting further work

We marked up the center blocks for a plane blade bed angle of 45 degrees, except for my Osage orange smoother, which will have a 50 degree bed angle.  We also marked the reverse slope, the shape of which is less critical, needing mainly enough room to get the fingers into the opening to remove stubborn shavings.  These cuts were made freehand (following a line) on the bandsaw.  The bedding angle cut was made on the table saw.

The forward slope was sanded on a belt sander, the bedding slope on a strip of sandpaper attached to a slab of marble.  We filed slight 90 degree bevels on the bottom of the bedding slope.

We measured and made crosspins (not shown) and rounded their tops.

Tomorrow we will drill the locations for the crosspins, install dowels in the front and back corners and glue the cheeks back onto the center blocks.  After allowing time for the glue to set up, we will begin the process of shaping the blanks into something more closely resembling the planes we will take home with us.

Norm

Preparing to Make Wooden Planes

Over the last few years, I've acquired a few wooden handplanes.  Several of them are older planes that I've not yet restored to working condition and they are basically sitting on the shelf for display.  But I also purchased a pair of planes--a smoothing plane and a 16" jack plane--from Scott Meek and I'm finding them really lovely to use.

Scott Meek jointer (rear) and smoothing planes

Scott offers plane-building classes in his Asheville, NC, workshop and in a few weeks I am scheduled for a week-long class to build three planes:

• A smoothing plane
• A jack plane
• A jointer plane

To get ready for the class, I've been reading and watching DVDs.  There are some good resources available.  In case you are interested in learning about making wooden planes, here's what I've found so far:

•  David Finck's Making & Mastering Wood Planes -- an excellent resource on making a Krenov-style smoothing plane; he also has a DVD set on making and using wooden planes
• John Whelan's Making Traditional Wooden Planes -- a brief description of how you can make not only a smoothing plane but also many other specialized types of planes
• David Perch and Robert Lee's Wooden Planes and How to Make Them -- similar to Whelan's book in that it covers many types of planes, but not the same ones as Whelan
• Scott Meek has a DVD set that shows his method for making Krenov-style planes

The books are mostly available from Amazon.com or Highland Woodworking.  Perch and Lee is sold by Lee Valley.  The Meek DVDs are available from Popular Woodworking.